(00) 1234 56780009

PROJECT BOARDS

 

FEATURES:

  • On-chip - 64KB flash Program memory ; 1792 bytes Expanded RAM (XRAM) ; 2048 bytes EEROM ; SPI interface ; 16-bit Programmable Counter Array for Compare, Capture, PWM ;
  • Three programmable Timer/Counters ; Two External Interrupts.
  • Operating Frequency – 11.0592 MHz.
  • RS232 compatible serial interface for communication and ISP
  • Alphanumeric 16x2 LCD display with back lighting
  • Two nos of general purpose LED’s.
  • Two-no.of general purpose push button Switches.
  • A Push button switch for Reset and a Slide switch to select either program mode or run mode.
  • Four no. of 8-pin single row Berg Sticks connected to PORT 0 to PORT 3.
  • Power Adaptor (5V, 1A.)
  • Evaluation version of ‘C’ compiler.
  • Demo programs for LCD, USART, LED switches.
  • 16 nos Flying leads with female bergs for extending IO lines

 

FEATURES

ATMEGA128 is a Low power, high performance 8-bit Microcontroller operating at 5 VDC. The controller is based on Reduced Instruction Set (RISC) architecture, and the instruction set and related decode mechanism are much simpler than those of micro programmed Complex Instruction Set Computers. This simplicity results in a high instruction throughput.

THE CONTROLLER INCLUDES THE FOLLOWING FEATURES:

  • 128KB flash program memory.
  • 4KB Internal Static RAM (SRAM).
  • 4KB of internal EEPROM.
  • Up to 64KB optional External Read/Write memory space.
  • 53 Programmable I/o lines.
  • On chip JTAG debugging and programming capability.
  • On chip In-System Programming (ISP) Capability.
  • Two 8-bit Timer/Counter and Two 16 –bit Timer/Counter
  • Capture, Compare and PWM modules.
  • On chip 8 Channel, 10-bit ADC module
  • Dual Programmable Serial USART’s.
  • Master/Slave SPI Serial Interface.
  • On-chip Two wire Serial Interface (I2C)
  • Watchdog Timer with On-chip oscillator.
  • On-chip analog Comparator.
  • Eight external Interrupts.
  • 16x2 alphanumeric display (LCD) with back lighting.
  • RS232C Serial interface through on chip UART0 or UART1 and 9 pin D-sub connector.
  • ISP downloading tool to download the code to controller Flash memory.
  • 4 nos 16 pin single row berg stick connected Port A to Port B
  • 2 nos of general purpose push button switches. A switch SW1 is for reset
  • 2 nos general purpose LED's and 1 power on LED
  • The software examples are compiled using WINAVR GCC compiler.
  • Unused controller lines terminated in berg headers.
  • Power supply adapter 230VAC to 5VDC, 1A.
  • Demo programs for LCD,USART,LED and Switches
  • 16 Nos flying leads for extending I/O lines
  • Evaluation version of complier

 

FEATURES:

  • 8K x 14 words of FLASH Program Memory ; 368 x 8 bytes of Data Memory (RAM).
  • 256 x 8 bytes of EEPROM Data Memory.
  • One External Interrupt pin ; Three programmable Timer/Counters.
  • Two Capture/Compare/PWM (CCP) modules ; SPI, I2C, USART
  • 8-channel, 10bit ADC ; In-Circuit Serial Programming™ (ICSP™) via two pins.
  • MPLAB® In-Circuit Debug (ICD) via two pins.
  • Operating Frequency - 8 MHz .
  • RS232 compatible serial interface for communication
  • Alphanumeric 16x2 LCD display.
  • Two numbers of general purpose LED’s.
  • Three numbers of push button Switches. One push button switch for reset and other two push button switches are general-purpose.
  • Two numbers of 20-pin single row Berg Sticks connected from Port A to Port E.
  • Power adaptor (5V, 1A.)
  • PIC CCS Evaluation Version.
  • Demo programs for LCD, USART, LED switches.
  • ICD dongle for programming debugging user program
  • 16 nos Flying leads with female bergs for extending IO lines

 

PIC 18F8680 PROJECT BOARD

FEATURES:

  • Program memory-64kb.
  • Data memory-3328bytes, EEPROM memory-1024 bytes.
  • Four external interrupt pins.
  • Four programmable Timer/Counters.
  • One Capture/Compare/PWM (CCP) module.
  • SPI, I2C, USART (RS232, RS485), CAN.
  • 16-channel, 10bit ADC.
  • In-Circuit Serial Programming™ (ICSP™) via two pins.
  • MPLAB® In-Circuit Debug (ICD) via two pins
  • Operating Frequency - 10 MHz.
  • RS232 compatible serial interface for communication and ISP.
  • Alphanumeric 16x2 LCD display.
  • Two nos of general purpose LED’s.
  • Two-no. of general-purpose push button Switches.
  • A Push button switch for Reset and a Slide switch to select either program mode or run mode.
  • Four no. of 20-pin single row Berg Sticks connected to Port A to Port H, Port J.
  • Power Adaptor (5V, 1A.)
  • PIC CCS Evaluation Version.
  • Demo programs for LCD, USART, LED switches.
  • ICD dongle for programming debugging user program
  • 16 nos Flying leads with female bergs for extending IO lines

 

FEATURES:

  • Useful as base board to develop project
  • Two UARTs available as 3 wire RS232 ports
  • (For SM2148)
  • 16x2 Alphanumeric LCD (For SM2148)
  • All port pins available on FRC connector for direct connection with other circuit
  • 9V, 500mA Adapter, serial cable provided
  • SM2148 : LPC2148 based add on module

 

FEATURES:

  • 400K System Gates
  • Up to 139 l/O pins
  • Up to 288K bits of total block RAM
  • Up to 56K bits of total distributed RAM
  • Eight global clock lines
  • Three power sources - 1.2 V,2.5V and 3.3 V
  • On board dockgeneration-50MHZ, 10MHZ, HZ, 1MHZ, 0KHZ and 100KHZ
  • On board regulators for required power supplies
  • JTAG connector for downloading the code into PROM and FPGA
  • On board 2MB PROM 1C (XCF2SV020)
  • A Push button switch for reset
  • Alphanumeric 16x1 LCD display
  • LED's provided for power indication and one LED for programming indication
  • Four 40 pin male berg connectors (CN2 to CN5) to extend 138 I/O lines.
  • A 9-pin D-type male Connector for power connection(+5VandGND
  • 38 no's of flying leads to extend the I/O lines to external circuitry
  • CD with sample example projects and XILINX ISE 10.1 Web Pack and manual
  • Parallel port based Programming cable
  • On board two 8 pin DIP switches (DIPT and DIP 2) for general purpose inputs with 16 pin connecting terminals (CN6)
  • 16 general purpose LED's with corresponding connecting terminals.
  • Two connectors for power supply to board (User can use either a POWER JACKor9 pin D-sub connector)

 

FEATURES:

  • Two sided solder masked FR4 PCB with plated through holes at 2.54mm pitch
  • Supply and ground tracks for ease of connection
  • Berg pins for connection to project boards using flying leads
  • Size 11 x 23 cms

 

PROJECT INTERFACE BOARD

FEATURES:

  • Interfacing with SPI devices
    • 12 bit DAC
    • 256K EEPROM
    • 12-bit ADC
  • Interfacing with I2C devices
    • RTC WITH LI-ION BATTERY
    • 16K NVROM
    • 8-bit DAC
  • Compare, Capture and PWM interfaces
  • On-chip Comparator test interface.
  • Provision for testing on-chip ADC.
  • RS485 interface.
  • Push button for external Interrupt testing.
  • Two no. of General purpose LED’s.
  • Oscillator provision for testing on-chip RTC.
  • Provision for Pulse Input for testing counters.
  • Berg sticks for connecting above interfaces to project board using flying leads.

 

ARM Cortex M3 Project Board

ALS-PJTBRD-ARMCTXM3-01

Specifications:

  • LPC1768 is an ARM Cortex M3 based micro-controller for embedded applications requiring a high level of integration and low power dissipation
  • LPC1768 is a 32/16 bit controller with 512 bytes program flash and 64K bytes of RAM
  • 12M Hz crystal allows easy communication setup
  • On board voltage regulator for generating 3.3V from +5V input through power adapter
  • One serial MAX3232 interface with 9 pin DSUB connector for UART0 which is used by the boot loader program, to program LPC178 flash memory without external programmer
  • PIGGY BACK Module carrying LPC1768 Controller
  • Onchip ADC – one preset provided for study
  • LCD 16×2 alphanumeric display
  • One general purpose LED
  • Reset switch for resetting the controller
  • UART2 provision through 3 pin reliamate
  • USB 2.0 device full speed type B connector provided with USB link LED
  • Four 20 pin male berg sticks for extending controller signals to any interface board
  • 16 no's of flying leads for connecting interface board with project board
  • Standard JTAG connector with ARM 2×10 pin layout for programming/ debugging with ARM-JTAG
  • 20 pin Standard Trace Port for tracing CPU instruction execution
  • A number of software examples in 'C-language' to illustrate the functioning of the interfaces. The software examples are compiled using an evaluation version of KEIL4 'C' compiler for ARM
  • 5V ,1A DC adapter and RS232 cable are included

 

GSM BASED HOME SECURITY SYSTEM

ALS-PRJBRD-UCXP3-01

Feature Description  
Dual band - GSM 850 & EGSM 900 MHz
- PCS 1900 & DCS 1800 MHz
GPRS - multi slot Class 10 support
- Coding scheme CS-1, CS-2, CS-3 & CS-4
Features TCP/IP, FTP, HTTP, DATA, SMS
Interface Serial RS232 and TTL with all handshaking lines.
Power supply 9V-15V DC
Current Peak 1.8A and Average 0.35A.
RTC with battery backup
Operating Temperature 30c to +80c
SIM interface Supports SIM card 1.8V and 3V
Transmitting power - 2W at EGSM 900 & GSM 850
- 1W at DCS 1800 & PCS 1900

Other Specifications:

  • Status indication through NETWORK Led and POWER led
  • Power – 5V DC for project boards and 12V DC for GSM module.
  • MQ-6 sensor operates at 5V which senses the LPG gas leakage.
  • MOC7811 sensor used to sense smoke.
  • PIR sensor which operates at 5v, for sensing intruder.
  • GSM module can also be directly interfaced to PC through RS-232.
  • Microphone and External Speaker for voice interface with GSM module.
  • Buzzer and status LED for status indication.
  • Operates at a standard baud rate of 9600.
  • Berg sticks for connection to ALS Controller board through Flying leads.
  • Test points for observation purpose.
  • Board size 100 x 160mm.

 

GRAPHIC LCD DISPLAY INTERFACE WITH HALL EFFECT SENSOR

ALS-PRJBRD-UCXP4-01

Specifications:
The ALS-PRJBRD-UCXP4-01 Project board has the following features:

  • Graphic LCD display 128x64 dots - displays character and bitmap images.
  • Ultrasonic distance sensor – SHARP sensor (GP2Y0A21YK0F) -measures the object distance from 10 to 80 cm.
  • Hall Effect rpm sensor with DC motor carrying shaft mounted magnet. Speed of DC motor can be varied using external DC power supply.
  • Atmospheric pressure sensor – hp03s – measures 300 to 1100 hpa absolute pressure range with I2C interface.
  • All the above parameters are displayed on the graphic LCD.
  • Five keys for user interface.
  • Operating temperature is 0 to 50C.
  • One general RED LED for power indication.
  • Berg sticks for connecting project board to controller board using flying leads.
  • Power supply required +5V DC - on board regulator to generate +3.3V.
  • PCB size: 100mmX160mm.

 

RFID BASED ACCESS CONTROL

ALS-PRJBRD-UCXP6-01

The ALS-PRJBRD-UCXP6-01 allows the user to control the access of unauthorized persons using RFID technology. Project board has the following features:

  • RFID based access control board interfacing with microcontroller.
  • 13.56MHz MIFARE read/write module
    • Complete Read/Write module with built in transceiver antenna.
    • Auto checks for presence of tag.
    • TTL RS232 interface, baud rate 19200bps.
    • Secure Encrypted contactless communication.
    • Ideal for emoney,secure access and fast data collection applications.
    • Typical operating distance 0-60mm.
    • Operating voltage 3-5V DC(5V has been used)
    • 1 LED indicator
    • Unique serial number on each device.
  • MIFARE S50 tags.
  • 1X4 matrix keypad
  • Buzzer indication
  • 2 General purpose LEDs
  • Access control motor operating at 5V DC
  • Two nos of 5-pin and one no 3-pin single row Berg Sticks to connect to ALS controller board port lines.
  • 5 test points for observation purpose.
  • Flying leads for connecting power and signals to ALS controller board.
  • Demo program for access control using RFID.
  • Board size 100 x 160 mm.

 

BLUETOOTH BASED SERVO MOTOR CONTROL

ALS-PRJBRD-UCXP7-01

The Bluetooth based servomotor control project board allows position control of a DC servomotor over a range of +/- 90deg, based on commands sent through a Bluetooth module. Two numbers of HC-05 Bluetooth modules and one low end robotic servomotor are provided. In a typical experiment, one Bluetooth module is connected to an ALS controller board through the serial port while the other Bluetooth module is connected to a PC, also through a serial port. Terminal Software in the PC can be used to send data and receive data from the controller. Commands can be sent which will be suitably converted to PWM signal and output to servomotor.

SPECIFICATIONS:
The ALS-PRJBRD-UCXP7-01 Project board has the following features

BLUETOOTH MODULE (HC - 05)
Feature Description  
Radio Chip CSR BC417.
Memory External 8Mb Flash.
Band 2.4GHz radio transceiver.
Transmit power 4dBm to +6dBm Class2.
Power supply 3.1 to 4.2VDC, typically 3.3V.
Interface UART interface with programmable baud rate and default baud rate 38400.
Data rate Up to 3 Mbps, EDR (Enhanced data rate).
Sensitivity -80dBm typical.
Current 40mA MAX.
With integrated antenna.
Status LED to indicate the working mode.
SERVO MOTOR
Feature Description  
Control System Pulse width control, 1500usec neutral.
Operating Voltage: 4.8V – 6.0VDC.
Direction Counter clockwise/pulsewidth increasing from 800 to - 2200usec.
Operating Speed 0.33sec to rotate 60deg at no load.
Stall Torque: >=5.0Kgf.cm (69.44oz/in).
Running Current: 0.23A.
Output Angle: >= 170deg.
Operates at baud rate of 38400.
Commands can also be sent from an Android cell phone with suitable application installed.
Berg sticks for connection to ALS Controller board through Flying leads.
Test points for observation purpose.
Power – 5V DC for project boards.
Board size 100 x 160mm.

 

GPS COORDINATE LOCATOR

ALS-PRJBRD-UCXP2-01

Specifications:
The ALS-PRJBRD-UCXP2-01 project board has the following features:

  • GPS receiver module for obtaining time and navigation information from satellites.
  • Module finds application in GPS based clocks, Displays, Position Indicators etc.
  • Receiver Sensitivity: -160dBm.
  • Maximum navigation update rate is 10Hz.
  • Time taken for position fixing:
    • Cold start : 35s
    • Warmstart : 33s
    • Hotstart : 1s typical
  • Operational limits : Altitude below 18,000m and velocity less than 515m/s.
  • Provision for active and passive external antennas.
  • Rechargable 3.0V VL battery for storing configuration information.
  • The module operates off 5V DC supply, 35mA.
  • Storage and operating temperature: -40 to +85 deg C.
  • PCB size 65mm/40mm.
  • The serial protocol is industry standard NMEA 0183.
  • Operates at a standard baud rate of 9600.
  • Manufacturer’s software provided in CD allows the selection of required NMEA messages.
  • PRJBRD/UCXP2 (Project Board) has a Compass module for sensing the Temperature, Pressure and Heading inforation of the environment.
  • Specificaions of the Compass module is given below:
    • Integrated pressure sensor, 300-1100hpa absolute Pressure Range.
    • Temperature sensor of the range -20’C to +60’C.
    • Full integration of 2-axis magnetic sensors and electronics circuits resulting in less external components needed.
    • I2C Slave, FAST (=400 KHz) mode.
    • Power up/down function available through I2C interface.
    • 2.4V~3.6V wide power supply operation supported.
    • SET/RESET strap drive.
  • Single row Berg Sticks to connect to ALS controller board port lines.
  • Provision to connect the o/p of GPS module to the Controller serial port or to the serial port of a host system’s serial port for study purposes.
  • Power mate connector (5V,DC) (Connects to Power mate in ALS controller board).
  • Demo program for extracting latitude , longitude and Universal time information from the GPS receiver and displaying on the LCD in the Controller board.
  • Demo program for extracting Pressure, Temperature and heading information from compass module and displaying on the LCD in the Controller board.
  • Flying leads to connect to controller board.
  • Board size 100 x 160 mm.

 

TFT DISPLAY WITH TOUCH SCREEN & SDHC CARD

ALS-PRJBRD-UCXP8-01

Specifications:
The ALS-PRJBRD-UCXP8-01 Project board has the following features:

  • 2.4” TFT display
    • Operates at +3.3V
    • 240×320 TFT display with Touch screen & SD card socket
  • One LED for power indication.
  • 6-pin single row Berg Sticks to connect to ALS controller board port lines from TFT display control lines.
  • 10-pin single row Berg Sticks to connect the data lines of TFT display to controller board.
  • 8-pin single row Berg Sticks to connect SPI lines from controller board to project board.
  • Power mate connector (5V, DC) (Connects to Power mate in ALS controller board).
  • Demo programs for TFT display, touch interface & SDHC card operations.
  • Three test points for observation purpose.
  • Flying leads to connect to controller board.
  • Board size 100×160 mm.